差分跳频通信系统的特点及性能

文章介绍了一种新型的短波跳频通信技术——差分跳频,分析了差分跳频技术区别于常规跳频技术的主要特点。针对按序列检测的信号接收方法,对差分跳频通信系统在AWGN信道下的性能进行了理论分析,同时做出相应的计算机仿真,证实了差分跳频通信技术和按序列检测方法的结合,使通信系统在AWGN信道下的性能得到了比较显著的提升。     

Na+、K+离子交换对Co-Mo/MCM-41加氢脱硫催化剂的影响

 用偏硅酸钠和正硅酸乙酯作硅源制备了MCM-41（分别记作MCM-41(S)和MCM-41(T)）分子筛，并用Na₂C₂O₄和K₂C₂O₄对MCM-41(S)进行了碱金属离子交换改性。以质量分数0.8 %的二苯并噻吩（DBT）的十氢萘溶液为模型化合物，考察了不同MCM-41担载的Co-Mo硫化物催化剂对DBT的加氢脱硫反应性能。结果表明，MCM-41担载的Co-Mo催化剂加氢活性较低，DBT主要通过直接脱硫反应路径脱硫。其活性顺序为：Co-Mo/MCM-41(T)>Co-Mo/MCM-41(S)>Co-Mo/MCM-41(K)>Co-Mo/MCM-41(Na)。UV-Vis结果表明，部分Co与MCM-41(S)中少量Al发生相互作用，生成了CoAl₂O₄，是造成Co-Mo/MCM-41(S)活性降低的重要因素。而在Co-Mo/MCM-41(K)和Co-Mo/MCM-41(Na)中，除CoAl₂O₄物种之外，碱金属的引入还促进了Co₃O₄物种的形成，使其活性进一步降低。     

光纤光栅感温火灾探测报警系统在原油罐区的应用

通过对现有罐区火灾自动报警技术的认真考察、对比,在石西集中处理站原油罐区安装了光纤光栅感温火灾探测报警系统.该报警系统的传感信号是光的波长变化,传感器及其探测系统是靠光缆连接而进入被测现场,它具有高安全性、高可靠性、高绝缘性、高抗电磁干扰性、防潮耐蚀、寿命长等其他传统火灾探测报警系统无法比拟的优越性能.阐述了其系统构成和运行效果.该系统在石西集中处理站运用效果良好.     

Fenton试剂降低采油污水CODCr的研究与应用

针对辽河油区超稠油采油污水的特点，采用Fenton试剂催化氧化，对采油污水处理进行研究。实验研究及现场应用结果表明，此方法对污水的CODCr具有良好的去除效果。处理后污水经过简单生化，进一步降解污染物，能够实现稳定迭标排放，且具有能耗低、运行成本低和操作简单等特点。     

相关条件下基于N-P准则的分布式检测理论研究

本文针对并行网络、二元局部判决的情况,研究了在相关条件下基于N-P准则的分布式检测融合算法,给出了在联合概率密度已知和未知两种情况下的最优融合规则的理论推导及相应的解决方案,并在实验仿真的基础上,得到了部分有益的结论。     

一种的四进制CPM调制器的设计与FPGA实现

设计并实现了一种基于FPGA的四进制连续相位调制器（PCM）。该调制器的基带调制模块通过查表法实现，复杂度较低。仿真结果验证了设计的正确性。     

Pack cementation process for the formation of refractory metal modified aluminide coatings on nickel-base superalloys

The vapour phase compositions of a series of pack powder mixtures containing elemental Al and Hf or W powders as depositing sources and CrCl₃·6H₂O or AlF₃or CrF₃as activators were analysed in an attempt to further develop the pack cementation process to codeposit Al and Hf or W to form diffusion coatings on nickel base superalloys. The results suggested that Al could be codeposited with Hf, but not with W, from the vapour phase. Compared with both AlF₃and CrF₃, CrCl₃·6H₂O has been shown to be a more suitable activator for codepositing Al with Hf. The optimum coating temperature was identified to be in the range of 1050°C to 1150°C. Based on the thermochemical analysis, a series of coating deposition studies were undertaken, which confirmed that codeposition of Al and Hf could be achieved at a deposition temperature of 1100°C in the CrCl₃·6H₂O activated packs containing elemental Al and Hf powders. The coating obtained had a multilayer structure consisting of a Ni₇Hf₆Al₁₆top layer and a NiAl layer underneath, followed by a diffusion zone, which revealed that the coating was formed by the outward Ni diffusion. It is suggested that the compositions suitable for codeposition of Al and Hf could be effectively identified by comparing the vapour pressures of HfCl₄and HfCl₃with that of AlCl in the packs activated by chloride salts. It has also been experimentally demonstrated that, although W could not be deposited from the vapour phase, a high volume of fine W particles can be entrapped into the outer NiAl coating layer formed by the outward Ni diffusion using a modified pack configuration. This leads to the formation of a composite coating layer with W particles evenly distributed in a matrix of NiAl. It is suggested that this modified pack process could be similarly applied to develop nickel aluminide coatings containing other refractory metals that may not be codeposited with Al from the vapour phase.     

新型槽栅nMOSFET热载流子效应的模拟研究

应用二维器件仿真程序 PISCES- ,对槽栅结构和平面结构器件的特性进行了模拟比较 ,讨论了槽栅结构 MOSFET的沟道电场特征及其对热载流子效应的影响。槽栅结构对抑制短沟道效应和抗热载流子效应是十分有利的 ,而此种结构对热载流子的敏感 ,使器件的亚阈值特性、输出特性变化较大     

Breaking a remote user authentication scheme for multi-server architecture

Lin et al., (2003) proposed a remote user authentication scheme for multi-server architecture. In this paper, we breaks this scheme by giving an attack. Our attack allows an adversary to impersonate any user in the system, as long as a single authentication message of that user is observed.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.